• Accepts Fiber with Cladding Diameters from 80 µm to 400 µm
• Strip Polyimide Coatings with Diameters 100 µm - 250 µm, 400 µm, or 500 µm
• Mechanical Blade with a Lifetime of 100 - 200 Strips
• Manual Rotation with 20 Detent Positions at 18° Apart
• Includes Top Inserts and Rear Guides
• Includes Tools for Installing Bottom Inserts and Front Guides
• Requires a Fiber Holder Insert Set (Sold Separately Below)

The FWS100 stripper removes polyimide coating from fibers with cladding diameters from 80 µm to 400 µm and coating diameters of 100 µm to 250 µm, 400 µm, or 500 µm. The rotation barrels on either end of the stripper are used to hold an optical fiber under tension. Users can strip 1 mm to 50 mm long window regions by moving the sliding stops to achieve the desired distance; see the image to the lower left.

This stripper is optimized for quick, precise removal of coating with high repeatability and ease of use. A scale that measures 50 mm is provided under the blade for reference; for precise stripping, the fiber should be marked beforehand. The height of the blade can be set by pushing down on the round handle and adjusting the micrometer so the blade makes contact with the coating. Users manually strip the fiber by moving the blade from right to left. The fiber can be rotated in increments of 18° using the rotation knob located on the left side of the unit. For detailed instructions on how to load and strip the fiber, see the manual by clicking the red docs icon () below.

Each rotation barrel requires a bottom insert, top insert, rear guide, and front guide to properly hold a fiber in place during the stripping process. The FWS100 Window Stripper includes two top inserts and two rear guides that are pre-installed in the rotation barrels; see the image to the lower right. These can be used with any fiber size and should not be removed by the user. One fibe holder insert set is required to be purchased separately below. Each set includes two bottom inserts and two front guides. The inserts grip the fiber in place, while the guides keep the fiber close to the center of rotation.

A tool kit and 100 replacement blades are included with the FWS100 stripper. Each unit is shipped with a power supply and location-specific power cord.

Click to Enlarge
Features of the FWS100 Window Stripper

Click to Enlarge
The FWS100 Window Stripper includes two rear guides and two top inserts. One insert set, which includes two front guides and two bottom inserts, is required to be purchased separately below. The VHW250 insert set is shown here.

Click to Enlarge
Figure 2: Front guides can be secured by tightening the screw with the included screwdriver.

Click to Enlarge
Figure 1: Bottom inserts can be secured by tightening the setscrew on the barrel with the included 0.050" balldriver.

• One is Required to Use the FWS100 Window Stripper
  • VHW250: Accepts Ø100 µm - Ø250 µm Fiber
  • VHW400: Accepts Ø400 µm Fiber
  • VHW500: Accepts Ø500 µm Fiber
• Bottom Inserts Grip Fiber within the Rotation Barrels
• Front Guides Keep Fiber Close to the Center of Rotation

A Fiber Holder Insert Set must be purchased with the FWS100 window stripper to secure the fiber. Each set includes two bottom inserts and two front guides. Each insert is designed to grip the fiber within the rotation barrels. The guides sit beside the barrels and keep the fiber close to the center of rotation.

We offer three fiber holder insert sets that are compatible with specific fiber coating diameters: VHW250 for Ø100 µm to Ø250 µm, VHW400 for Ø400 µm, and VHW500 for Ø500 µm. The VHW250 set has inserts equipped with rubber where the fiber is placed and guides for a range of smaller fibers. The VHW400 and VHW500 sets have inserts with a V-groove designed to hold Ø400 µm or Ø500 µm coated fibers, respectively. Both of these sets include the same front guides, which support Ø400 µm to Ø500 µm coated fiber. Each V-groove insert and each guide is engraved with the largest compatible fiber coating diameter, in microns.

Users will need to install their fiber holder insert set into the FWS100 Window Stripper using its included tool kit. The inserts can be placed into the bottom slots of the rotation barrels and secured by tightening the two setscrews with the 0.050" balldriver, as shown in Figure 1. The guides can be inserted into the front guide holders, where they will help constrain fiber position to the rotational axis. The guides can be secured by tightening the screw with the screwdriver, as shown in Figure 2.

• Replacement Blades for the FWS100 Window Stripper
• Single-Sided 1.53" (38.9 mm) Long Blade
• Lifetime of 100 - 200 Strips
• User-Installable
• Pack of 100

The FWSBLADE is a pack of 100 replacement blades for the FWS100 Window Stripper. These blades are designed to cut polyimide-coated fiber at a specific angle with the FWS100. A single blade has a lifetime of 100 - 200 strips. Blade replacement instructions are provided in the FWS100 user manual. Be sure to use caution when handling a blade and dispose it in a proper container, such as our FTDU Disposal Unit.